Design OVERVIEW
• WORKING TIME 1 hr- 1 hr, 30 mins
• TOTAL TIME 1 hr- 1 hr, 30 mins
• SKILL LEVEL Intermediate
• ESTIMATED COST$ 10 and over
Replacing a ceiling light institution is frequently necessary because an old institution has worn out, but it’;s also generally done as part of a scenery overhaul. A new light institution can make a huge difference in the look and sense of a room. The work itself is generally relatively easy, though anytime you’;re working with electricity there’;s some peril. DIYers should have a introductory understanding of how electrical circuits work, and some experience with analogous repairs, before trying light institution relief.
Like plumbing, electrical repairs are frequently fairly simple if the system is fairly new and follows accepted practices. But they can come veritably delicate veritably snappily if the wiring system turns out to be old or in poor condition. Any time you take on wiring systems, be willing to call an electrician to bail you out if effects get complicated.
Before You Begin
Turn the wall power switch controlling the light institution to the OFF position. If there’;s any chance another person could turn on the switch while you’;re working(e.g., children or a partner), also turn off the power at the main service panel.
What You will Need
Outfit/ Tools
• Screwdriver
•Non-contact circuit tester
Accoutrements
• New ceiling light institution
• Line connectors( line nuts)
• Electrical vid( if demanded)
Instructions
1. Remove the Old Light Institution
Remove the institution shade or globe. How you do this will depend on the type of institution you have. It can involve loosening little screws holding the shade in place, unhooking some mounting clips( as shown then), or just coiling a glass shade from the base of the institution.
Once the ceiling institution shade is removed, separate the institution base from the ceiling box by coiling the mounting screws or the knurled clump that holds the institution to the ceiling box.
2. Test for Power and Dissociate the Cables
Once the institution base is separated from the ceiling box, check for power by using anon-touch circuit tester to make sure there’;s no current flowing to the cables.
Dissociate the light institution from the circuit cables by coiling the line connectors. The institution may also have a bobby grounding line attached to the mounting swatch on the box or to the circuit grounding line. Dissociate this, as well. Set away the detached light institution.
Eventually, remove the old underpinning swatch that’;s secured to the ceiling box. The new institution will come with its own underpinning swatch.
3. Prepare the New Ceiling Fixture
Unbox the new ceiling institution. Precisely remove the glass shade and set it away in a safe place. Remove the plastic bag containing the tackle and set it away, as well. Remove the institution base from the box and examine its cables. عمومًا, it’;ll have three line leads a black hot line, a white neutral line, and a green or bare bobby ground line.
ما يزال, the black and white cables for each socket may not yet be connected together, If the light institution has two or further beaconsockets.However, join the white cables together with a line connecter( generally included with the light institution), If this is the case. Join the black line leads together as well.
Read the light institution instructions to determine how your light institution will be mounted to the ceiling box. This can vary, depending on the size and weight of the light institution. Occasionally, it’;ll be a simple matter of deforming the light institution base directly to the ceiling box. With other styles, a mounting swatch is first attached to the ceiling box, also the institution base is squinched to a mounting swatch. With heavier institutions, a threaded mounting tube is squinched into a hole on the mounting swatch, also the institution base is threaded over the tube and secured with a screw- on clump.
4. Install the Mounting Swatch
ما يزال, first examine the swatch included with the new light institution, If your light institution requires the use of a mounting swatch( it generally does). It’;ll have several small threaded screw holes in it, some of which are used to attach the swatch to the ceiling box, others which will be used to support the light institution base. The swatch also has a larger threaded hole in the center; this is used if the light institution is supported via a threaded mounting tube that screws into the swatch.
ضع الحامل مقابل قاعدة مؤسسة الضوء لتحديد فتحات المسامير التي سيتم استخدامها لدعم المؤسسة.
ايضا, قم بتوصيل حامل التثبيت بصندوق السقف, باستخدام أي فتحات مسامير تصطف مع صندوق السقف. قد تعطيك تعليمات المؤسسة الخفيفة أيضًا إرشادات حول الطريقة الصحيحة لإرفاق حامل التثبيت.
ما يزال, قم بضغط قضيب التثبيت الملولب في الفتحة المركزية على الحامل, إذا كانت مؤسستك تتطلب ذلك. يستخدم هذا بشكل عام للأضواء الثقيلة, similar as chandeliers and other hanging light institutions.
5. Check the Circuit Cables
In utmost cases, the circuit cables you preliminarily disconnected will be suitable to attach incontinently to the new light institution. You’;ll see one line with white sequestration( this is the neutral), another with black sequestration( this is the hot line), and another that’;s bare bobby or covered with green sequestration( this is the ground line). قد يكون الخط الأرضي للدائرة متصلاً بمسمار أرضي أخضر في الجزء الخلفي من الصندوق.
نصيحة
ما يزال, قد لا يكون الترميز اللوني واضحًا, أو قد يكون عزل الكابلات متصدعًا أو قديمًا, إذا كانت الأسلاك في منزلك قديمة حقًا, دعم العزل حول الكابلات القديمة عن طريق ربطها بفتحة كهربائية, اذا كان ضروري. يجب أن يغطي الفيديو الكهربائي العزل حتى الجزء المكشوف المكشوف في نهاية السطر.
6. قم بتوصيل الكابلات الأرضية
The ground connection on a ceiling light institution can vary, depending on the type of institution and ceiling box you have. Just remember that the light institution’;s ground lead must have a essence pathway to the circuit grounding line. It’;s dangerous to install a ceiling institution without this ground pathway.
ما يزال, also the situation is easy Just attach the circuit ground line directly to the institution’;s ground lead, using a line connector, If your ceiling box is plastic.
It’;s a little more complicated if the ceiling box is essence. Then, both the box and the light institution need to be connected to the circuit ground line. A common way to do this is to circle the circuit ground line around a green ground screw on the mounting swatch or on the essence box, also attach the free end of the ground line to the institution’;s ground lead. Alternatively, if the circuit ground line is formerly attached to the essence box, the light institution’;s ground lead can be attached to the mounting swatch.
نصيحة
Making the line connections for the light institution can be a little tricky since you’;re holding the institution in skyline at the same time you’;re trying to connect it to the circuit cables. Having a coadjutor on a alternate graduation hold the institution while you make the line connections can make this much easier.
7. Connect the Neutral and Hot Cables
Join the circuit neutral line to the institution’;s neutral lead( both cables generally have white sequestration), using a line connector.
Do the same with the circuit and institution hot cables( both generally have black sequestration).
8. Mount the Institution Base
With the cables connected, the coming step is to attach the institution base to the ceiling box. Depending on the style, the base may be attached with two long screws that thread into screw holes on the mounting swatch, أو مع كتلة مخرشة تثبت على قضيب التثبيت الملولب بعد انزلاق قاعدة المؤسسة فوقه.
عندما يستخدم التثبيت مسامير طويلة, قد يستغرق الأمر بعض المناورة لإخراج البراغي من خلال العزل في قاعدة المؤسسة وخيوطها في صندوق السقف. قد يكون للمؤسسة ثقب المفتاح- أماكن برغي على شكل تسمح لك أولاً بتركيب البراغي في صندوق السقف, قم أيضًا بدفع المؤسسة فوق البراغي ولفها قليلاً لتثبيتها على البراغي. Formerly in place, strain the screws down forcefully so the institution base is tight against the ceiling.
9. Install Light Bulbs and Shade
Complete the job by installing light bulbs( do not exceed the total wattage standing of the institution). Turn the power back on, also turn on the light switch to test the operation of thefixture.However, install the globe or shade, as directed by the manufacturer, If the institution operates rightly.
